Decree No. 311 / 2021 Coll.
Decree amending Decree No. 226 / 2015 Coll., on the principles for defining the emergency planning zone and the procedure for defining it, and on the details of the content of the external emergency plan and its structure
Valid
Order
Effective from 01.01.2022
Text versions:
01.01.2022
27.08.2021
311
DECLARATION
of 19 August 2021
amending Decree No. 226 / 2015 Coll., on the principles for the definition of the emergency planning zone and the procedure for defining it and on the details of the content of the external emergency plan and its structure
According to Section 54 (3) of Act No. 224 / 2015 Coll., on the prevention of major accidents caused by selected hazardous chemicals or chemical mixtures and amending Act No. 634 / 2004 Coll., on Administrative Charges, as amended, (Act on the Prevention of Major Accidents):
Decree No. 226 / 2015 Coll., on the principles for the definition of the emergency planning zone and the procedure for its definition and on the details of the contents of the external emergency plan and its structure, is amended as follows:
1. in Article 2 (c):
"(c) a modification factor of a numerical value that characterises the expected consequences by type-scenario and hazard of a substance or group of substances of the same classification and similar physicochemical properties that affect the determination of the size of the emergency planning zone;"
2. in Paragraph 4 (1), the word "or" shall be deleted in point (e), at the end of paragraph 1, the dot shall be replaced by the comma and the word "or" and the following point (g) shall be added:
"(g) using risk analysis and evaluation outputs (11), in compliance with the rules set out in Annex 1, Section 3, unless the starting limit can be determined in accordance with points (a) to (f).
11) Article 9 of Act No. 224 / 2015 Coll., Decree No. 227 / 2015 Coll., on the formalities for security documentation and the extent of information provided to processors by the assessment. '.
3. Annex 1 shall read as follows:
"Annex No 1 to Decree No. 226 / 2015 Coll.
Definition of emergency planning zones
a) Creating a device inventory
1. Information shall be collected on all equipment and methods of transport of hazardous substances in the premises. For each installation, further information shall be found to determine the maximum quantity of dangerous substances which may cause a major accident by their dangerous effects and the relevant category of dangerous substances as defined in Tables I and II of Annex 1 to the Act. This is based on the operator's documentation, in particular the documentation for the establishment of the emergency planning and processing area of the external emergency plan, the safety report (in particular the risk assessment of a major accident), the internal emergency plan and other necessary data requested by the county authority, as well as the data requested by the fire brigade of the county according to Act No. 239 / 2000 Coll., on the Integrated Rescue System and on the amendment of certain laws, as amended. The device shall be entered in Table A.2, column 2, followed by the appropriate name of the dangerous substance and the hazard category in column 1. In Table A.2. also the equipment in the buildings designated under Section 7 (1) of the Act is included.
2. A pipeline shall also be considered as an installation where it connects two installations where the sum of their preliminary parameters 1 calculated in accordance with point (e) of this section is less than their distance. For multiple interconnections of two devices, the first sentence shall be considered separately for each line. In the case of a line between two devices, the route can be divided into separate sections, meaning the fittings of the separately closed part of the pipe. These are automatic or remote-controllable fittings with an independent source of energy, or shut-off fittings which, in case of loss of control, close themselves with force of gravity, spring or pressure.
(b) Assignment of accident type scenarios
1. One or more type scenarios according to Table A.3 shall be assigned to each individual installation in column 4 based on the type of dangerous substance. Devices with a hazardous substance not listed in Table A.3 shall be assigned to the hazard category of the hazardous substance in accordance with Table A.4. Where multiple type scenarios are assigned to a hazardous substance, those scenarios for the installation concerned shall be indicated in column 4 as separate items, in separate rows. The following principles, respecting the type of equipment, shall be followed when assigning a type scenario:
1.1 The amount of hazardous substance in linked sources of risk is not added when the FireBall from BLEVE type scenario is assigned; individual devices are assessed separately. It shall be evaluated by the quantity in one container.
1.2 The type scenario FireBall from BLEVE is not assigned for atmospheric storage, for storage in cylinders, for manifold distribution of flammable gases and for underground storage tanks and semi-sealed storage tanks.
2. In the case of underground gas storage probes, the type scenario shall not be assigned.
(c) Determination of hazardous substances
1. For each installation, column 3 and 5 of Table A. 2. the quantity of dangerous substance placed and the state in which the substance is present. Where devices are interconnected and do not have sufficient effective separation between them, the sum of the quantities of the hazardous substance in those devices shall be used to determine the quantity of the hazardous substance used to determine the type scenario.
2. The existence of separate sinks for individual tanks with sufficient distance between the edge of the pit and other tanks, the use of automatic or remote-controlled shut-off fittings with an independent source of energy, the shut-off fittings which, in the event of loss of control, close themselves, or a sufficiently durable mechanical barrier between devices shall be considered to be effective separation.
3. In the case of a gas pipe installation for which it is not possible to determine the maximum quantity of dangerous substance from the operator's documentation, the maximum quantity of dangerous substance shall be determined in accordance with Chart 6. The maximum amount of the hazardous substance determined in accordance with Chart 6 may not exceed the sum of the maximum quantities of the hazardous substance in the gas-connected pipeline installations.
4. For surface technologies of the underground gas storage tank, including extraction probes, the pressure is given instead of the quantity of the hazardous substance, the preliminary parameter 1 is deducted from Table A.3.
(d) Calculation of the effective amount of hazardous substance
The effective amount of the dangerous substance shall be calculated by multiplying the maximum quantity of the dangerous substance (column 5 of Table A.2) by the relevant modification factor of the dangerous substance listed in Table A.3. or by the relevant modification factor of the dangerous substance listed in Table A.4.
For toxic liquids, the maximum amount of dangerous substance shall be determined by:
1. for the chemicals listed in Table A. 3. by multiplying the quantity of hazardous substance by the coefficient of fumes KV, which is subtracted from Table A. 1. using equation 1,
2. for chemicals and mixtures not listed in Table A. 3. by multiplying the quantity of dangerous substance by the coefficient of fumes KV, to be deducted from Table A. 1. using equation 1.
The resulting value is entered in column 7 of Table A.2.
For surface technologies of underground gas storage tanks, including extraction probes, no effective amount is determined.
(e) Determination of preliminary parameter 1
The preliminary parameter 1 shall be determined on the basis of its constant value as shown in Table A.3. or Table A. 4. or on the basis of Chart 1, 2, 3, 4 or 5 according to the relevant type scenario. The resulting value shall be given in column 8 of Table A.2. The preliminary parameter 1 is determined separately for each item as the separate row of Table A.2. If the distance from graphs cannot be subtracted for a small value of effective quantity, the preliminary parameter 1 of 50 m shall be determined.
(f) Determination of parameter L
The L parameter shall be determined as the maximum achieved value of all preliminary parameters 1 obtained in accordance with the procedure referred to in point (e) of this section. The L parameter shall be entered in column 9 of Table A.2.
Legend:
ground design furnished
Emergency planning zone
boundary of the area for which the internal emergency plan is being processed
default limit
the smallest circle inscribed around the floor plan projection furnished with centre S and radius r
Parameter established according to Annex 1
centre of the device
Figure 1
Model for setting the starting limit according to § 4 (1) (a)
Description: r < 1 / 5 L, H = circle with centre in S and radius of L.
Figure 2
Model for setting the starting limit according to § 4 (1) (a)
Description: r < 1 / 5 L (the L parameter is significantly larger than the size of the device, but the dimensions of the area for which the internal emergency plan is being processed are not negligible in terms of size).
Figure 3
Model for setting the starting limit according to § 4 (1) (b)
Description: Distance L3 determined as distance to both sides of the pipe axis (P)
Figure 4
Model for setting the starting limit according to § 4 (1) (c)
Description: Devices with different type scenarios
Figure 5
Model for setting the starting limit according to § 4 (1) (d)
Description: r > 1 / 5 L (the calculated L parameter is in obvious disproportion to the device dimensions).
Figure 6
Model for setting the starting limit according to § 4 (1) (e)
Description: distance L shall be determined for all surface technologies of the underground gas storage tank and all operating (pressurised - sampling) probes of the underground gas storage tank (PZP) within one protected area for special interference with the Earth's PZP bark and operated by one operator
CH - protected area for special interference with the earth's crust of the underground gas container
PT - surface technology of the central area or centre
PS - operating probe
Figure 7
Model for setting the starting limit according to § 4 (1) (f)
Equation 1:
Tk = T- TtTv-Tt
where:
TK temperature coefficient for conversion of quantities of toxic liquids;
T storage temperature or process temperature; If the storage temperature is less than 5 ° C, the temperature shall be 5 ° C; Tt melting temperature (rigidity) at normal pressure (° C); Tv temperature boiling under normal pressure (° C).
The boiling and melting temperatures are specified in the safety data sheet. Storage temperature or temperature in the process specified in the safety documentation. Normal pressure means a pressure of 101,325 kPa. When a dangerous substance is used in an installation at different temperatures, equipment with a specific different temperature is recorded and assessed as a separate device in Table A.2..
Table A. 1: Subtracting the vapour coefficient
| Teplotní koeficient (TK) | Koeficient výparu (KV) |
|---|---|
| Větší než 0,95 | 1 |
| 0,8 – 0,95 | 0,5 |
| 0,6 – 0,8 | 0,15 |
| 0,4 – 0,6 | 0,05 |
| 0,2 – 0,4 | 0,01 |
| Menší než 0,2 | 0,005 |
Table A.2: List of devices
| 1. | 2. | 3. | 4. | 5. | 6. | 7. | 8. | 9. | |
|---|---|---|---|---|---|---|---|---|---|
| Nebezpečná látka | Zařízení | Skupenství*) | Typový scénář**) | Maximální množství m (t) / maximální tlak p (MPa) ***) | Modifikační faktor | Efektivní množství me (t) | Předběžný parametr l (m) | Parametr L (m) | |
| Název | Kategorie nebezpečnosti podle směrnice 2012/18/EU | ||||||||
*) In the case of toxic liquids, the storage temperature or the process in ° C shall also be placed in brackets.
* *) In the case of toxic liquids, the vapour coefficient (Kv) shall be placed in brackets.
* * *) In the case of surface technologies of the underground gas storage tank, including extraction probes, the pressure value is given instead of the quantity of dangerous substance.
Table A. 2.1: Model for filling in table A.2.
| 1. | 2. | 3. | 4. | 5. | 6. | 7. | 8. | 9. | |
|---|---|---|---|---|---|---|---|---|---|
| Nebezpečná látka | Zařízení | Skupenství | Typový scénář | Maximální množství m t)/maximální tlak p (MPa) | Modifikační faktor | Efektivní množství me (t) | Předběžný parametr l (m) | Parametr L (m) | |
| Název | Kategorie nebezpečnosti podle Směrnice 2012/18/EU | ||||||||
| Automobilový benzín | P5a Hořlavá kapalina, kat. 1 | Zásobník atmosférický | kapalina | EXPL | 7 000 t | 0,035 | 245 t | 800 m | 800 m |
| Potrubí | kapalina | EXPL | 0,5 t | 0,035 | 0,0175 t | 35 m | 35 m | ||
| Autocisterna | kapalina | EXPL FIRE | 28,5 t | 0,035 | 0,9975 t | 130 m | 200 m | ||
| 0,85 | 24,225 t | 200 m | |||||||
| Chlor | H2 Akutní toxicita, kat. 2 | Zásobník | zkapalněný plyn | TOX | 50 t | 0,35 | 17,5 t | 2 300m | 2300m |
| Železniční cisterna | zkapalněný plyn | TOX | 45 t | 0,35 | 15,75 t | 2 150m | 2150 m | ||
| Potrubí | zkapalněný plyn | TOX | 0,4 t | 0,35 | 0,141 | 150 m | 150 m | ||
| Formaldehyd, 32% | H2 Akutní toxicita, kat. 3 | Zásobník | kapalina (20°C) | TOX, Kv = 0,01 | 860t | 0,03 | 0,258 t | 410 m | 410m |
| ... | ... | ... | ... | ... | ... | ... | |||
| LPG | P2 Hořlavý plyn, kat. 1 | Zásobníkové pole (3x96 t) | plyn | EXPL FIRE | 288 t | 0,1 | 28,8 t | 400 m | 580 m |
| 96 t | 1 | 96 t | 580 m | ||||||
| ... | ... | ... | ... | ... | ... | ... | |||
| Kyslík | P4 Oxidující plyny, kat. 1 | Zásobník | plyn | OXI | 330 t | 1 | 330 t | 80 m | 80 m |
| ... | ... | ... | ... | ... | ... | ... | |||
| Zemní plyn | P2 Hořlavý plyn, kat. 1 | Těžební sonda | plyn | - | <10MPa | - | 80 m | 80 m | |
| ... | ... | ... | ... | ... | ... | ... | |||
| Perunit | P1a Výbušniny, | Sklad | tuhá látka | EXPL | 45 t | 1 | 45 t | 460 m | 460 m |
| oddíl 1.1 | ... | ... | ... | ... | ... | ... | ... | ||
Table A.3: Type scenarios and modification factors for the substances listed by name
| Nebezpečné látky | Číslo CAS (je uváděno pouze pro informaci) | Typový scénář | Graf | Modifikační faktor |
|---|---|---|---|---|
| Dusičnan amonný, definovaný podle řádky č. 1 Tabulky II, přílohy č. 1 zákona | Exploze výbušnin a směsí | EXPL | 0,0025 | |
| Dusičnan amonný definovaný podle řádky č. 2 Tabulky II, přílohy č. 1 zákona | Exploze výbušnin a směsí | EXPL | 0,005 | |
| Dusičnan amonný definovaný dle řádky č. 3 Tabulky II, přílohy č. 1 zákona | Exploze výbušnin a směsí | EXPL | 0,01 | |
| Dusičnan amonný definovaný dle řádky č. 4 Tabulky II, přílohy č. 1 zákona | Exploze výbušnin a směsí | EXPL | 0,5 | |
| Dusičnan draselný definovaný dle řádky č. 5 Tabulky II, přílohy č. 1 zákona | Exploze výbušnin a směsí | EXPL | Modifikační faktor se neurčuje, parametr /je konstantně 50 m. | |
| Dusičnan draselný definovaný dle řádky č. 6 Tabulky II, přílohy č. 1 zákona | Exploze výbušnin a směsí | EXPL | Modifikační faktor se neurčuje, parametr /je konstantně 50 m. | |
| Oxid arseničný, kyselina arseničná nebo její soli | 1303-28-2 | Toxický únik | TOX | 0,01 |
| Oxid arsenitý, kyselina arsenitá nebo její soli | 1327-53-3 | Toxický únik | TOX | 0,2 |
| Brom | 7726-95-6 | Toxický únik | TOX | 0,121 |
| Chlor | 7782-50-5 | Toxický únik | TOX | 0,35 |
| Sloučeniny niklu v inhalovatelné práškové formě: oxid nikelnatý, oxid nikličitý, sulfid nikelnatý, sulfid niklitý, oxid niklitý | Toxický únik | TOX | 0,02 | |
| Ethylenimin | 151-56-4 | Toxický únik | TOX | 0,862 |
| Fluor | 7782-41-4 | Toxický únik | TOX | 0,54 |
| Formaldehyd (koncentrace rovno nebo větší 90%) | 50-00-0 | Toxický únik | TOX | 0,1 |
| Vodík | 1333-74-0 | Výbuch mraku par (VCE) | EXPL | 0,2 |
| Chlorovodík | 7647-01-0 | Toxický únik | TOX | 0,03 |
| Alkyly olova | Toxický únik | TOX | 0,588 | |
| Zkapalněné hořlavé plyny, kateg. 1 nebo 2 (včetně LPG) a zemní plyn (včetně upraveného bioplynu definovaného podle řádky č. 18 Tabulky II, přílohy č. 1 zákona o prevenci závažných havárií | Výbuch mraku par (VCE) | EXPL | 0,1 | |
| FireBall z BLEVE | FIRE | 1 | ||
| Zemní plyn v podzemních zásobnících plynu v přirozených vrstvách, vodonosných vrstvách a kavernách | Modifikační faktor se neurčuje, předběžný parametr 1 je konstantně 250 m od oplocení areálu podzemních zásobníků plynu, 150 m od provozní sondy s tlakem na ústí nad 10 MPa a 80 m pro provozní sondy s tlakem na ústí do 10 MPa včetně. | |||
| Acetylen | 74-86-2 | Výbuch mraku par (VCE) | EXPL | 0,1 |
| Ethylenoxid | 75-21-8 | Toxický únik | TOX | 0,4 |
| Propylenoxid | 75-56-9 | Toxický únik | TOX | 0,4 |
| Methanol | 67-56-1 | FireBall z BLEVE | FIRE | 0,33 |
| Výbuch mraku par (VCE) | EXPL | 0,007 | ||
| 4, 4'-Methylene bis (2-chloraniline) nebo jeho soli, v práškové formě | 101-14-4 | Toxický únik | TOX | 2 |
| Methylisokyanát | 624-83-9 | Toxický únik | TOX | 133 |
| Kyslík | 7782-44-7 | Podporování požáru | OXI | 1 |
| 2,4 -Toluen diisokyanát 2,6 -Toluen diisokyanát | 584-84-9 91-08-7 | Toxický únik | TOX | 3,571 |
| Karbonyldichlorid (fosgen) | 75-44-5 | Toxický únik | TOX | 7,4 |
| Arsan (arsenovodík) | 7784-42-1 | Toxický únik | TOX | 1,17 |
| Fosfan (fosforovodík) | 7803-51-2 | Toxický únik | TOX | 4,55 |
| Chlorid sirnatý | 10545-99-0 | Zóna havarijního plánování se nestanovuje. | ||
| Oxid sírový | 7446-11-9 | Toxický únik | TOX | 0,666 |
| Polychlordibenzofurany a polychlordibenzodioxiny (včetně TCDD), kalkulované jako ekvivalent TCDD | Toxický únik | TOX | 58 | |
| Tyto KARCINOGENY nebo směsi obsahující tyto karcinogeny v koncentracích vyšších než 5 % hmotnostních: 4-aminobifenyl nebo jeho soli, benzotrichlorid, benzidin nebo jeho soli, bis(chlormethyl)ether, chlormethylmethylether, 1,2-dibrommethan, diethylsulfát, dimethylsulfát, dimethylkarbamoylchlorid, 1,2-dibrom-3-chlorpropan, 1,2-dimethylhydrazin, dimethylnitrosoamin, hexamethylfosfotriamid, hydrazin, 2-nafthylamin nebo jeho soli, 4-nitrodifenyl a 1,3 propansulton | Toxický únik | TOX | 10 | |
| Ropné produkty a alternativní paliva | ||||
| a) benzíny a primární benzíny, | FireBall z BLEVE | FIRE | 0,85 | |
| Výbuch mraku par (VCE) | EXPL | 0,035 | ||
| b) letecké petroleje (včetně paliva pro reaktivní motory), | FireBall z BLEVE | FIRE | 0,75 | |
| Požár kapalin | P-FIRE | 0,59 | ||
| c) plynové oleje (včetně motorové nafty, topných olejů pro domácnost a směsí plynových olejů), | FireBall z BLEVE | FIRE | 0,76 | |
| Požár kapalin | P-FIRE | 0,6 | ||
| d) těžké topné oleje, | FireBall z BLEVE | FIRE | 0,76 | |
| Požár kapalin | P-FIRE | 0,37 | ||
| e) alternativní paliva sloužící ke stejným účelům a mající podobné vlastnosti, pokud jde o hořlavost a nebezpečnost pro životní prostředí, jako produkty uvedené v písmenech a), b), c) nebo d). | Typový scénář se volí podle podobností s písmeny a), b), c) nebo d) ropných produktů a alternativních paliv, podle kterých došlo k zařazení | |||
| Bezvodý amoniak | 7664-41-7 | Toxický únik | TOX | 0,025 |
| Fluorid boritý | 7637-07-2 | Toxický únik | TOX | 0,11 |
| Sirovodík | 7783-06-4 | Toxický únik | TOX | 1 |
| Piperidin | 110-89-4 | Toxický únik | TOX | 0,1 |
| Výbuch mraku par (VCE) | EXPL | 0,007 | ||
| Bis(2-dimethylaminoethyl)(methyl)amin | 3030-47-5 | Toxický únik | TOX | 0,1 |
| 3 -(2-ethylhexyloxy)propylamin | 5397-31-9 | Toxický únik | TOX | 0,1 |
| Směsi (*) chlornanu sodného klasifikované ve třídě akutní toxicita pro vodní prostředí, kategorie 1 [H400] obsahující méně než 5 % aktivního chlóru a neklasifikované v žádné jiné kategorii nebezpečnosti podle řádku č. 41 Tabulky II, přílohy č. 1 zákona ------------------------------------------------------- | Zóna havarijního plánování se nestanovuje. | |||
| (*) Za předpokladu, že směs při nepřítomnosti chlornanu sodného nebude klasifikována ve třídě akutní toxicita pro vodní prostředí 1 [H400] | ||||
| Propylamin definovaný dle řádky č. 42 Tabulky II, přílohy č. 1 zákona | 107-10-8 | Toxický únik | TOX | 0,01 |
| Výbuch mraku par (VCE) | EXP | 0,007 | ||
| Tert-butyl-akrylát definovaný dle řádky č. 43 Tabulky II, přílohy č. 1 zákona | 1663-39-4 | Výbuch mraku par (VCE) | EXPL | 0,007 |
| Toxický únik | TOX | 0,036 | ||
| 2-methyl-3-butennitril definovaný dle řádky č. 44 Tabulky II, přílohy č. 1 zákona | 16529-56-9 | Toxický únik | TOX | 0,017 |
| Výbuch mraku par (VCE) | EXPL | 0,007 | ||
| Tetrahydro-3,5-dimethyl-l,3,5-thiadiazin-2-thion (Dazomet) definovaný dle řádky č. 45 Tabulky II, přílohy č. 1 zákona | 533-74-4 | Zóna havarijního plánování se nestanovuje. | ||
| Methylakrylát definovaný dle řádky č. 46 Tabulky II, přílohy č. 1 zákona | 96-33-3 | Toxický únik | TOX | 0,037 |
| Výbuch mraku par (VCE) | EXPL | 0,007 | ||
| 3-methylpyridin definovaný dle řádky č. 47 Tabulky II, přílohy č. 1 zákona | 108-99-6 | Toxický únik | TOX | 0,01 |
| 1-brom-3-chlorpropan definovaný dle řádky č. 48 Tabulky II, přílohy č. 1 zákona | 109-70-6 | Toxický únik | TOX | 0,037 |
Table A. 4: Type scenarios and modification factors for substances classified by hazard category
| Kategorie nebezpečnosti v souladu s nařízením (ES) č. 1272/2008 | Typový scénář | Graf | Modifikační faktor |
|---|---|---|---|
| H1 Akutní toxicita kategorie 1, všechny cesty expozice | Toxický únik | TOX | 1 nebo modifikační faktor podle tabulky A. 5 (použije se v případě, že látku lze považovat za extrémně toxickou) |
| H2 Akutní toxicita — kategorie 2, všechny cesty expozice | Toxický únik | TOX | 0,17 |
| — kategorie 3, inhalační cesta expozice | Toxický únik | TOX | 0,03 |
| H3 Toxicita pro specifické cílové orgány -jednorázová expozice | Toxický únik | TOX | 0,03 |
| P1a Výbušniny — Nestabilní výbušniny, nebo — výbušniny, oddíl 1.1, 1.2, 1.3, 1.5 nebo 1.6, nebo — látky nebo směsi, které mají výbušné vlastnosti podle metody A. 14 podle nařízení (ES) č. 440/2008 | Exploze výbušnin a směsí | EXPL | 1 |
| P1b Výbušniny Výbušniny, oddíl 1.4 | Exploze výbušnin a směsí | EXPL | Modifikační faktor se neurčuje, parametr je / konstantně 50 m. |
| P2 Hořlavé plyny Hořlavé plyny, kategorie 1 nebo 2 | FireBall z BLEVE | FIRE | 1 |
| Výbuch mraku par (VCE) | EXPL | 0,1 | |
| P3a Hořlavé aerosoly („Hořlavé" aerosoly kategorie 1 nebo 2 obsahující hořlavé plyny kategorie 1 nebo 2 nebo hořlavé kapaliny kategorie 1 | Výbuch mraku par (VCE) | EXPL | 0,01 |
| P3b Hořlavé aerosoly „Hořlavé" aerosoly kategorie 1 nebo 2 neobsahující hořlavé plyny kategorie 1 nebo 2 ani hořlavé kapaliny kategorie 1 | Požár kapalin | P-FIRE | 1 |
| P4 Oxidující plyny Oxidující plyny, kategorie 1 | Podporování požáru | OXI | 1 |
| P5a Hořlavé kapaliny — Hořlavé kapaliny, kategorie 1, nebo | FireBall z BLEVE | FIRE | 0,85 |
| — hořlavé kapaliny kategorie 2 nebo 3 udržované za teplot nad jejich bodem varu nebo — jiné kapaliny s bodem vzplanutí < 60 °C, udržované za teplot nad jejich bodem varu | Výbuch mraku par (VCE) | EXPL | 0,035 |
| P5b Hořlavé kapaliny — Hořlavé kapaliny kategorie 2 nebo 3, u kterých zejména podmínky zpracování jako vysoký tlak nebo vysoká teplota mohou vytvořit nebezpečí závažné havárie, nebo — jiné kapaliny s bodem vzplanutí < 60 °C, u kterých zejména podmínky zpracování jako vysoký tlak nebo vysoká teplota mohou vytvořit nebezpečí závažné havárie | Výbuch mraku par (VCE) | EXPL | 0,007 |
| P5c Hořlavé kapaliny Hořlavé kapaliny kategorie 2 nebo 3 nespadající pod položky P5a a P5b | BoilOver | FIRE | 0,01 |
| P6a Samovolně reagující látky a směsi a organické peroxidy Samovolně reagující látky a směsi, typ A nebo B, nebo organické peroxidy, typ A nebo B | Exploze výbušnin a směsí | EXPL | 0,25 |
| P6b Samovolně reagující látky a směsi a organické peroxidy Samovolně reagující látky a směsi, typ C, D, E nebo F, nebo organické peroxidy, typ C, D, E nebo F | Požár kapalin | P-FIRE | Modifikační faktor se neurčuje, parametr je / konstantně 50 m. |
| P7 Samozápalné kapaliny a tuhé látky Samozápalné kapaliny, kategorie 1 Samozápalné tuhé látky, kategorie 1 | Podporování požáru | OXI | 0,5 |
| P8 Oxidující kapaliny a tuhé látky Oxidující kapaliny, kategorie 1, 2 nebo 3, nebo oxidující tuhé látky, kategorie 1, 2 nebo 3 | Podporování požáru | OXI | Modifikační faktor se neurčuje, parametr je / konstantně 50 m. |
| E1 Nebezpečnost pro vodní prostředí v kategorii akutní 1 nebo chronická 1 | Zóna havarijního plánování se nestanovuje. | ||
| E2 Nebezpečnost pro vodní prostředí v kategorii chronická 2 | Zóna havarijního plánování se nestanovuje. | ||
| 01 Látky nebo směsi se standardní větou o nebezpečnosti EUH014 - Prudce reaguje s vodou | Exploze výbušnin a směsí | EXPL | Modifikační faktor se neurčuje, parametr je / konstantně 50 m. |
| 02 Látky a směsi, které při styku s vodou uvolňují hořlavé plyny kategorie 1 | Výbuch mraku par (VCE) | EXPL | Modifikační faktor se neurčuje, parametr je / konstantně 50 m. |
| 03 Látky nebo směsi se standardní větou o nebezpečnosti EUH029 - Uvolňuje toxický plyn při styku s vodou | Toxický únik | TOX | Modifikační faktor se neurčuje, parametr je / konstantně 50 m. |
Table A. 5: Modification factors for extremely toxic substances. The largest modification factor found shall be used.
| Odhad akutní toxicity (jedná se o hodnotu LC50 nebo LD50, která je pro danou látku k dispozici) | Modifikační faktor |
|---|---|
| 0,05 < LD50 (mg/kg, oral) ≤ 0,5 | 10 |
| 0,5 < LD50 (mg/kg, dermal) ≤ 5 | |
| 1 < LC50 (ppmv, inh., 4h) ≤ 10 | |
| 0,005 < LC50 (mg/l, inh., 4h) ≤ 0,05 | |
| 0,005 < LD50 (mg/kg, oral) ≤ 0,05 | 100 |
| 0,05 < LD50 (mg/kg, dermal) ≤ 0,5 | |
| 0,1 < LC50 (ppmv, inh., 4h) ≤ 1 | |
| 0,0005 < LC50 (mg/l, inh., 4h) ≤ 0,005 | |
| 0,0005 < LD50 (mg/kg, oral) ≤ 0,005 | 1000 |
| 0,005 < LD50 (mg/kg, dermal) ≤ 0,05 | |
| 0,01 < LC50 (ppmv, inh., 4h) ≤ 0,1 | |
| 0,00005 < LC50 (mg/l, inh., 4h) ≤ 0,0005 | |
| 0,00005 < LD50 (mg/kg, oral) ≤ 0,0005 | 10000 |
| 0,0005 < LD50 (mg/kg, dermal) ≤ 0,005 | |
| 0,001 < LC50 (ppmv, inh., 4h) ≤ 0,01 | |
| 0,000005 < LC50 (mg/l, inh., 4h) ≤ 0,00005 | |
| (pokračovat dále v násobcích 10) |
Chart 1: Determination of preliminary parameter l for toxic leakage type scenario (TOX)
Chart 2: Determination of preliminary parameter l for explosive and mixture explosion type scenarios and vapour explosion (VCE)
Chart 3: Determination of preliminary parameter l for FireBall type scenarios from BLEVE and BoilOver (FireBall)
Graph 4: Determination of preliminary parameter l for type scenario liquid fire (P-FIRE)
Chart 5: Determination of preliminary parameter l for fire support type scenario (OXI)
Chart 6: Determination of the amount of gas leaked from the overhead pipeline
Rules for setting the L parameter using the results of the analysis and risk assessment
1. Selection of the type scenario: it is related to the individual physicochemical properties of chemicals and mixtures and the method of handling and respects the type scenarios according to Table A. 3 and A. 4.
2. Quantities of dangerous substances and mixtures: account is taken of the quantity which is actually expected to be involved in the accident. This does not need to be the quantity proposed in the installation, but the reduction must be defined and justified, for example by the nature of the technological process.
3. The speed of release of hazardous substances into the air: the release rate respects the physical state and conditions of the substance (e.g. storage form as liquefied or compressed gas, steam tension above the surface, concentration of hazardous substance in the mixture during leakage, powder or compact form of the substance).
4. Reducing factors: can only be counted for effective separation to prevent leakage, possibly reducing leakage from equipment (passive safety barriers). Organisational measures, i.e. mitigation requiring active intervention by operators or rescue personnel, cannot be counted.
5. Limit effects on human health (substance concentration, heat flow, overpressure): recommended are the lowest estimated values that can cause death to a person who is not an extremely susceptible individual.
6. Fire-related technical and explosive characteristics of substances / mixtures: use of only supported values of fire-related technical and explosive characteristics of substances / mixtures.
7. Atmospheric conditions: it is recommended to use air stability class D according to Pasquill and wind speed 3 m / s or less, or worse, values of dispersion conditions. If other variance conditions are used, this choice shall be justified.
8. Temperature of dangerous substance: the temperature of the substance is taken into account in equipment, including in exceptional technological conditions.
9. Gas density for the dispersion model: the choice is made according to the molecular mass of the hazardous substance, the concentration and temperature of its mixture with air (e.g. the diffusion model "Heavy gas dispersion").
10. Time and speed of leakage of dangerous substance from the device: both values must be justified. If this is not the case, the time of leakage of all expected quantities in 30 minutes shall be taken into account. If justified leakage time values are used, these values shall be equal to at least the time needed to identify the accident plus 10 minutes.
11. Calculation of liquid leakage: the nature of the device shall be taken into account. From an escaped substance formed by a puddle of justified dimensions, or a puddle of an area corresponding to the dimensions of the canister.
12. Quantities of hazardous substances involved in reaction: for explosives, the maximum quantity present in a particular warehouse or facility. In the case of flammable gases and vapours, it shall be stated which part of the leaked quantity is involved in the reaction, the models used and the input conditions used. ';
Transitional provision
The emergency planning zone defined in accordance with Decree No. 226 / 2015 Coll., as effective before the date of entry into force of this Decree, for toxic liquids, for substances promoting combustion or for petroleum substances shall be defined in the manner laid down in Decree No. 226 / 2015 Coll., as effective from the date of entry into force of this Decree, within 12 months of the date of entry into force of the Decree.
Efficacy
This Decree shall take effect on 1 January 2022.
Minister:
Hamlet v. r.
Sign in for notes, favorites and notifications
Regulation Information
| Citation | Decree No 311 / 2021 Coll., amending Decree No. 226 / 2015 Coll., on the principles for the definition of the emergency planning zone and the procedure for its definition and on the details of the contents of the external emergency plan and its structure |
|---|---|
| Regulation Type | Order |
| Author | - |
| Collection | Code of Laws |
| Date of Promulgation | 27.08.2021 |
|---|---|
| Effective from | 01.01.2022 |
| Effective until | - |
| Status | Valid |
Legal Areas:
Security
Administrative law
Public Contracts 2
Aktualizace zásad pro vymezení zón havarijního plánování a postupů při jejich vymezení u všech dotče...
Pardubický kraj
TLP, spol. s r.o.
261 360 CZK
24.08.2022
dodávka ručního RTG spektrometru
Puncovní úřad
BAS Rudice spol. s r.o.
400 000 CZK
06.04.2021
Notifications
Source:
Hlídač státu
(CC BY 3.0 CZ)
The regulation text is for informational purposes only.
Comments 0